|Table of Contents|

Experiment and Numerical Simulation on Bond-slip Behavior Between Angle Steel and Concrete(PDF)

《建筑科学与工程学报》[ISSN:1673-2049/CN:61-1442/TU]

Issue:
2020年06期
Page:
81-90
Research Field:
Publishing date:

Info

Title:
Experiment and Numerical Simulation on Bond-slip Behavior Between Angle Steel and Concrete
Author(s):
ZHAO Wei-ping1 WANG Zhen-xing1 DONG Peng-kun1 ZHU Bin-rong2 CHEN Hui-ling1
1. School of Mechanics and Civil Engineering, China University of Mining and Technology-Beijing, Beijing 100083, China; 2. China Electric Power Research Institute, Beijing 100192, China.
Keywords:
angle steel concrete ultimate bond strength numerical simulation bond mechanism transfer length
PACS:
TU375
DOI:
-
Abstract:
In order to study the interface bond behavior between angle steel and concrete, 9 angle steel concrete specimens were designed with the bond length, protective layer depth and concrete strength as parameters. The load-slip curves at the loaded end were obtained, and the influence of each parameter on the ultimate bond strength was analyzed. The calculation formula for the bond strength of interface was proposed, and compared with the test results, they agreed well with each other. Based on the interface Coulomb friction law and restart analysis technology, a refined finite element model was established to precisely simulate the gradual peeling process of the bond interface. Based on the research parameters, a calculation formula of transfer length was proposed, and compared with numerical simulations, which proved the applicability of the formula.The results show that the tip of the angle steel has a strong cracking effect, and the development of cracks during the pushing process will significantly reduce the bond strength. The ultimate bond strength increases with the increasing of concrete strength and protective layer depth, however decreases approximately linearly with the increasing of bond length. The load-slip curves of loaded end include chemical adhesion section, ascending section, descending section and residual section, and the interface bond mechanism and composition of bond stress are different at each stage. The damage of the bond interface gradually expands from loaded end to free end, and the transfer length of the bond stress remains constant during the propagation.

References:

[1] 赵鸿铁.组合结构设计原理[M].北京:高等教育出版社,2005. ZHAO Hong-tie.Design Theory of Composite Structure[M].Beijing:Higher Education Press,2005.
[2]ROEDER C W.Composite and Mixed Construction[M].New York:ASCE,1984.
[3]BRYSON J O,MATHEY R G.Surface Condition Effect on Bond Strength of Steel Beams in Concrete[J].Journal of ACI,1962,59(3):397-406.
[4]张 誉,李向民,李 辉,等.钢骨高强混凝土结构的粘结性能研究[J].建筑结构,1999,29(7):3-5,32. ZHANG Yu,LI Xiang-min,LI Hui,et al.Study on Bond Behavior Between Composite Steel Shape and High Strength Concrete[J].Building Structure,1999,29(7):3-5,32.
[5]李方元,赵人达.不同混凝土基体与变形钢筋的粘结滑移特性[J].工业建筑,2002,32(10):31-33,12. LI Fang-yuan,ZHAO Ren-da.The Bond-slip Behaviors Between Different Strength Concrete and Deformed Reinforcing Bars[J].Industrial Construction,2002,32(10):31-33,12.
[6]赵鸿铁.钢与混凝土组合结构[M].北京:科学出版社,2001. ZHAO Hong-tie.Steel and Concrete Composite Structure[M].Beijing:Science Press,2001.
[7]郑山锁,杨 勇,薛建阳,等.型钢混凝土粘结滑移性能研究[J].土木工程学报,2002,35(4):47-51. ZHENG Shan-suo,YANG Yong,XUE Jian-yang,et al.Study on Bond Slip Performance Between Steel and Concrete in SRC Structures[J].China Civil Engineering Journal,2002,35(4):47-51.
[8]郑山锁,邓国专,杨 勇,等.型钢混凝土结构黏结滑移性能试验研究[J].工程力学,2003,20(5):63-69. ZHENG Shan-suo,DENG Guo-zhuan,YANG Yong,et al.Experimental Study of Bond-slip Performance Between Steel and Concrete in SRC Structures[J].Engineering Mechanics,2003,20(5):63-69.
[9]杨 勇,郭子雄,薛建阳,等.型钢混凝土粘结滑移性能试验研究[J].建筑结构学报,2005,26(4):1-9. YANG Yong,GUO Zi-xiong,XUE Jian-yang,et al.Experiment Study on Bond Slip Behavior Between Section Steel and Concrete in SRC Structures[J].Journal of Building Structures,2005,26(4):1-9.
[10]李 红,刘伯权,吴 涛,等.T型钢与混凝土粘结滑移破坏机理研究[J].四川建筑科学研究,2010,36(5):45-48. LI Hong,LIU Bo-quan,WU Tao,et al.Failure Mechanism Study on the Bond-slip Between T Section Steel and Concrete in SRC Structures[J].Sichuan Building Science,2010,36(5):45-48.
[11]王 军.内配格构式角钢圆钢管混凝土力学性能研究及应用[D].杭州:浙江大学,2018. WANG Jun.Research and Application on the Mechanical Properties of Concrete-filled Circular Steel Tubes with Latticed Steel Angles Inside[D].Hangzhou:Zhejiang University,2018.
[12]邓文琴,张建东,刘 朵,等.角钢剪力连接件力学性能推出试验研究[J].建筑结构学报,2015,36(增1):389-395. DENG Wen-qin,ZHANG Jian-dong,LIU Duo,et al.Push-out Test Research on Mechanical Property of Angle Connector[J].Journal of Building Structures,2015,36(S1):389-395.
[13]SCHNEIDER S P.Axially Loaded Concrete-filled Steel Tubes[J].Journal of Structural Engineering,1998,124(10):1125-1138.
[14]康希良,程耀芳,涂 昀,等.钢管混凝土粘结-滑移性能试验研究及数值分析[J].工程力学,2010,27(9):102-106. KANG Xi-liang,CHENG Yao-fang,TU Yun,et al.Experimental Study and Numerical Analysis of Bond-slip Performance for Concrete Filled Steel Tube[J].Engineering Mechanics,2010,27(9):102-106.
[15]王 振,张 宁.钢管混凝土的界面黏结-滑移性能数值分析研究[J].中外公路,2018,38(1):192-200. WANG Zhen,ZHANG Ning.Numerical Analysis on Bond-slip Behavior of Concrete-filled Steel Tubes[J].Journal of China & Foreign Highway,2018,38(1):192-200.
[16]赵卫平,朱彬荣.高温后HSC粘结滑移基础参数测量与3D有限元数值模拟[J].工程力学,2017,34(4):177-186. ZHAO Wei-ping,ZHU Bin-rong.Basic Parameters Test and 3D Modelling of Bond in HSC After Elevated Temperatures[J].Engineering Mechanics,2017,34(4):177-186.
[17]郑山锁,李 磊.型钢高强高性能混凝土结构基本性能与设计[M].北京:科学出版社,2012. ZHENG Shan-suo,LI Lei.The Basic Property and Design of Steel Reinforced High Strength and High Performance Concrete[M].Beijing:Science Press,2012.
[18]孙宏友.基于正交试验法的透水混凝土配合比设计和试验研究[D].成都:西南交通大学,2016. SUN Hong-you.Experimental Research and Mix Proportion Design of Porous Concrete Based on Orthogonal Test Method[D].Chengdu:Southwest Jiaotong University,2016.
[19]应武挡,陈宗平.型钢高强混凝土界面黏结传力机理及影响因素分析[J].土木工程学报,2016,49(9):53-63,71. YING Wu-dang,CHEN Zong-ping.Interface Bond Force Transfer Mechanisms and Its Influence Analysis Between Shape Steel and High-strength Concrete[J].China Civil Engineering Journal,2016,49(9):53-63,71.
[20]GB 50010—2010,混凝土结构设计规范[S]. GB 50010—2010,Code for Design of Concrete Structures[S].
[21]BEHNOOD A,GHANDEHARI M.Comparison of Compressive and Splitting Tensile Strength of High-strength Concrete with and Without Polypropylene Fibers Heated to High Temperatures[J].Fire Safety Journal,2009,44(8):1015-1022.
[22]赵卫平.基于ANSYS接触分析的粘结-滑移数值模拟[J].建筑科学与工程学报,2011,28(2):44-51. ZHAO Wei-ping.Bond-slip Numerical Simulation Based on ANSYS Contact Analysis[J].Journal of Architecture and Civil Engineering,2011,28(2):44-51.
[23]LUNDGREN K.Pull-out Tests of Steel-encased Specimens Subjected to Reversed Cyclic Loading[J].Materials and Structures,2000,33(7):450-456.
[24]LEE C,LEE S,SHIN S.Modeling of Transfer Region with Local Bond-slip Relationships[J].ACI Structural Journal,2017,114(1):187-196.

Memo

Memo:
-
Last Update: 1900-01-01