«上一篇/Previous Article|本期目录/Table of Contents|下一篇/Next Article»

《建筑科学与工程学报》[ISSN:1673-2049/CN:61-1442/TU]

卷:

40卷

期数:

2023年05期

页码:

69-77

栏目:

建筑结构

出版日期:

2023-09-15

文章信息/Info

Title:

Experimental study on shear behavior of new partially encased I-steel composite beams

文章编号:

1673-2049(2023)05-0069-09

作者:

辛 力¹,刘 源¹,姚怡帆²,黄 华²,高 悦²

(1. 中国建筑西北设计研究院有限公司,陕西 西安 710018; 2. 长安大学 建筑工程学院,陕西 西安 710061)

Author(s):

XIN Li¹, LIU Yuan¹, YAO Yifan², HUANG Hua², GAO Yue²

(1. China Northwest Architecture Design and Research Institute Co., Ltd, Xi'an 710018, Shaanxi, China; 2. School of Civil Engineering, Chang'an University, Xi'an 710061, Shaanxi, China)

关键词:

新型部分填充工字钢组合梁;  受剪性能;  试验测试;  承载力;  计算方法

Keywords:

new partially encased I-steel composite beam;  shear behavior;  experimental test;  bearing capacity;  calculation method

分类号:

TU398

DOI:

10.19815/j.jace.2021.12124

文献标志码:

A

摘要:

为增大钢材利用率,提高组合梁受剪性能,提出了一种新型部分填充工字钢组合梁,并以栓钉排布方式、剪跨比以及混凝土填充量为参变量,采用“力-位移控制”的加载方式,对4根新型组合梁及对比工字钢梁进行了静力荷载作用下的受剪性能试验研究; 对比分析了新型组合梁和对比工字钢梁受力过程中的破坏形态、剪力-转角曲线、剪力-应变曲线以及承载力变化情况。结果表明:剪跨比1.6≤λ≤2.0的组合梁发生剪压破坏,剪跨区有贯通的主斜裂缝; 剪跨比为1.15的组合梁发生斜压破坏,剪跨区形成多个受压短柱,混凝土大面积剥落; 剪跨比从1.6减小至1.15时,极限承载力相应提高了31.8%; 混凝土的存在使新型组合梁的受剪承载力较普通的工字钢梁提高了33.3%; 翼缘栓钉的存在提高了组合梁截面的组合作用,使混凝土能充分发挥其抗压能力,极限受剪承载力相应提高了5.8%～29.1%,组合梁延性和刚度也相应增大; 结合试验实测数据,基于新型部分填充工字钢组合梁的构造特点,采用组合结构设计规范中受剪承载力计算公式,公式计算值与试验值吻合较好,该公式可为实际工程中的结构设计提供一定参考。

Abstract:

In order to increase the utilization rate of steel and improve the shear behavior of composite beams, a new type of partially encased I-steel composite beam was proposed. Experimental study on shear behavior of four new composite beams and a contrast I-steel beam under static load was carried out with stud arrangement, shear span ratio and concrete filling amount as parameters, and “force-displacement control” loading method was adopted. The failure mode, shear-rotation curve, shear-strain curve and bearing capacity of the new composite beam and the contrast I-steel beam in the stress process were compared and analyzed. The results show that the composite beam with shear span ratio 1.6≤λ≤2.0 occurs shear compression failure, and the shear span area has the through main oblique cracks. The composite beam with shear span ratio 1.15 occurs tilting pressure failure. Multiple compression short columns are formed in the shear span area, and the concrete is peeled off in large area. When the shear span ratio is reduced from 1.6 to 1.15, the ultimate bearing capacity is increased by 31.8%. The shear capacity of the new composite beam is 33.3% higher than that of the ordinary I-steel beam due to the existence of concrete. The existence of flange studs improves the combined action of composite beam section, so that the concrete can give full play to its compressive capacity. The ultimate shear capacity is increased by 5.8%-29.2%, and the ductility and stiffness of composite beams are also increased. Based on the experimental data and the structural characteristics of the new partially encased I-steel composite beam, the shear capacity calculation formula in the design specification of composite structures is adopted. The calculated values of the formula are in good agreement with the experimental values. The formula can provide some reference for structural design in practical engineering.

参考文献/References:

[1] 郝际平,孙晓岭,薛 强,等.绿色装配式钢结构建筑体系研究与应用[J].工程力学,2017,34(1):1-13.
HAO Jiping,SUN Xiaoling,XUE Qiang,et al.Research and applications of prefabricated steel structure building systems[J].Engineering Mechanics,2017,34(1):1-13.
[2]曹 杨,陈沸镔,龙 也.装配式钢结构建筑的深化设计探讨[J].钢结构,2016,31(2):72-76.
CAO Yang,CHEN Feibin,LONG Ye.Discussion on the detailed design of fabricated steel structure building[J].Steel Construction,2016,31(2):72-76.
[3]Eurocode 4:design of composite steel and concrete structures — part 1-1:general rules and rules for buildings:EN 1994-1-1:2004[S].Brussels:CEN,1994.
[4]聂建国,王洪全.钢-混凝土组合梁纵向抗剪的试验研究[J].建筑结构学报,1997,18(2):13-19.
NIE Jianguo,WANG Hongquan.Experimental study on longitudinal splitting strength of composite steel-concrete beams[J].Journal of Building Structures,1997,18(2):13-19.
[5]聂建国,陈 林,肖 岩.钢-混凝土组合梁正弯矩区截面的组合抗剪性能[J].清华大学学报(自然科学版),2002,42(6):835-838.
NIE Jianguo,CHEN Lin,XIAO Yan.Composite shear behavior of steel-concrete composite beams under sagging moment[J].Journal of Tsinghua University(Science and Technology),2002,42(6):835-838.
[6]HOSSAIN K M A,MOL L,WHITE H D.Behaviour of thin walled composite beams and columns[C]//SHANMUGAM N E,RICHARD LIEW J Y,THEVENDRAN V.Proceedings of International Conference on Thin-walled Structures.Singapore:Elsevier,1998:321-328.
[7]LIANG Q Q,UY B,BRADFORD M A,et al.Ultimate strength of continuous composite beams in combined bending and shear[J].Journal of Constructional Steel Research,2004,60(8):1109-1128.
[8]胡夏闽,江雨辰,施 悦,等.部分外包混凝土简支组合梁受弯性能试验研究[J].建筑结构学报,2015,36(9):37-44.
HU Xiamin,JIANG Yuchen,SHI Yue,et al.Experimental study on flexural behavior of simply supported partially concrete encased composite beams[J].Journal of Building Structures,2015,36(9):37-44.
[9]江雨辰,胡夏闽,王建林.部分外包钢梁受力性能试验研究及有限元分析[J].建筑结构学报,2015,36(增1):343-348.
JIANG Yuchen,HU Xiamin,WANG Jianlin.Experimental investigation and finite element analysis on mechanical performance of partially concrete encased steel beams[J].Journal of Building Structures,2015,36(S1):343-348.
[10]HE J,LIU Y Q,CHEN A R,et al.Shear behavior of partially encased composite I-girder with corrugated steel web:experimental study[J].Journal of Constructional Steel Research,2012,77:193-209.
[11]HE J,LIU Y Q,LIN Z F,et al.Shear behavior of partially encased composite I-girder with corrugated steel web:numerical study[J].Journal of Constructional Steel Research,2012,79:166-182.
[12]HE J,LIU Y Q,CHEN A R,et al.Bending behavior of concrete-encased composite I-girder with corrugated steel web[J].Thin-walled Structures,2014,74:70-84.
[13]TSAVDARIDIS K D,D'MELLO C,HUO B Y.Experimental and computational study of the vertical shear behaviour of partially encased perforated steel beams[J].Engineering Structures,2013,56:805-822.
[14]JIANG Y C,HU X M,HONG W,et al.Experimental study and theoretical analysis of partially encased continuous composite beams[J].Journal of Constructional Steel Research,2016,117:152-160.
[15]WU K,LIN S Q,LIU X Y,et al.Experimental study on mechanical behavior of prefabricated PEC composite beams under cyclic loading[J].International Journal of Steel Structures,2020,20(3):725-741.
[16]杨明昌,罗文飞,王军杰,等.装配整体式混凝土梁受剪性能试验及有限元分析[J].混凝土,2021(2):110-114.
YANG Mingchang,LUO Wenfei,WANG Junjie,et al.Shear test and finite element analysis of assembled monolithic concrete beams[J].Concrete,2021(2):110-114.
[17]蒋丽忠,曾丽娟,孙林林.钢-混凝土连续组合梁腹板局部屈曲分析[J].建筑科学与工程学报,2009,26(3):27-31.
JIANG Lizhong,ZENG Lijuan,SUN Linlin.Local buckling analysis of web of continuous steel-concrete composite beam[J].Journal of Architecture and Civil Engineering,2009,26(3):27-31.
[18]赵倩倩,周学军,张 婷,等.新型外包钢与混凝土简支组合梁非线性有限元分析[J].建筑结构,2011,41(增1):1119-1123.
ZHAO Qianqian,ZHOU Xuejun,ZHANG Ting,et al.Nonlinear analysis on U-section steel-encased concrete composite beams[J].Building Structure,2011,41(S1):1119-1123.
[19]杜德润,孟德丽,蒋济同.新型外包钢-混凝土组合梁与普通钢-混凝土组合梁性能对比分析[J].工业建筑,2014,44(增):559-562,577.
DU Derun,MENG Deli,JIANG Jitong.Comparative analysis of behaviors of the new-type steel-encased concrete composite beams and the ordinary steel-concrete composite beams[J].Industrial Construction,2014,44(S):559-562,577.
[20]金属材料拉伸试验 第1部分:室温试验方法:GB/T 228.1—2010[S].北京:中国标准出版社,2010.
Metallic materials — tensile testing — part 1:method of test at room temperature:GB/T 228.1—2010[S].Beijing:Standards Press of China,2010.
[21]混凝土结构试验方法标准:GB/T 50152—2012[S].北京:中国建筑工业出版社,2012.
Standard for test methods of concrete structures:GB/T 50152—2012[S].Beijing:China Architecture & Building Press,2012.

相似文献/References:

[1]陈宝春,陈逸聪,周家亮,等.预应力UHPC槽形节段与整体式混凝土板组合梁受剪性能[J].建筑科学与工程学报,2024,41(03):54.[doi:10.19815/j.jace.2024.04031]
　CHEN Baochun,CHEN Yicong,ZHOU Jialiang,et al.Shear behavior of composite girder with prestressed UHPC channel segments and monolithic concrete slab[J].Journal of Architecture and Civil Engineering,2024,41(05):54.[doi:10.19815/j.jace.2024.04031]

备注/Memo

备注/Memo:

收稿日期:2021-12-13
基金项目:陕西省青年科技新星项目(2021KJXX-77); 陕西省科技厅重点研发计划项目(2023-YBGY-184); 中国博士后科学基金项目(2022M723005)
作者简介:辛 力(1981-),男,工学博士,高级工程师,E-mail:xinli1129@sina.com。
通信作者:姚怡帆(1995-),男,工学博士研究生,E-mail:yyf30727@163.com。

常用功能

更新日期/Last Update: 2023-09-01