|本期目录/Table of Contents|

[1]张 峰,高华睿,赵国浩.预应力混凝土梁斜裂缝倾角的概率计算模型[J].建筑科学与工程学报,2022,39(05):104-112.[doi:10.19815/j.jace.2021.11073]
 ZHANG Feng,GAO Hua-rui,ZHAO Guo-hao.Probabilistic Calculation Model of Inclined Crack Angle of Prestressed Concrete Beam[J].Journal of Architecture and Civil Engineering,2022,39(05):104-112.[doi:10.19815/j.jace.2021.11073]
点击复制

预应力混凝土梁斜裂缝倾角的概率计算模型(PDF)
分享到:

《建筑科学与工程学报》[ISSN:1673-2049/CN:61-1442/TU]

卷:
39卷
期数:
2022年05期
页码:
104-112
栏目:
结构工程
出版日期:
2022-09-30

文章信息/Info

Title:
Probabilistic Calculation Model of Inclined Crack Angle of Prestressed Concrete Beam
文章编号:
1673-2049(2022)05-0104-09
作者:
张 峰1,高华睿2,赵国浩1
(1. 山东大学 岩土与结构工程研究中心,山东 济南 250061; 2. 山东高速建设管理集团有限公司,山东 济南 250002)
Author(s):
ZHANG Feng1, GAO Hua-rui2, ZHAO Guo-hao1
(1. Geotechnical and Structural Engineering Research Center, Shandong University, Jinan 250061, Shandong, China; 2. Shandong Hi-speed Construction Management Group Co., Ltd, Jinan 250002, Shandong, China)
关键词:
预应力混凝土梁 斜裂缝倾角 贝叶斯理论 MCMC方法 概率模型
Keywords:
prestressed concrete beam inclined crack angle Bayesian theory MCMC method probabilistic model
分类号:
TU375
DOI:
10.19815/j.jace.2021.11073
文献标志码:
A
摘要:
针对预应力混凝土(PC)梁剪切斜裂缝倾角的大小,各国规范建议公式差异较大,尚没有明确的理论模型。基于贝叶斯理论,引入马尔科夫链-蒙特卡洛(MCMC)高效采样方法,根据选定的预应力混凝土梁斜裂缝倾角计算公式作为贝叶斯先验模型; 通过收集到的45组剪切斜裂缝数据,考虑了箍筋配筋率、箍筋强度、混凝土抗压强度、剪跨比和有效预应力参数,建立了修正的斜裂缝倾角计算模型。结果表明:先验模型的预测值和试验值比值的均值和变异系数分别为0.68和0.26,后验模型的预测值和试验值比值的均值和变异系数分别为0.98和0.25,预测值更加接近试验值; 基于先张法预应力混凝土空心板梁实测斜裂缝倾角验证计算模型,先验模型的预测值和试验值比值的均值和变异系数分别为0.57和0.19,后验模型的预测值和试验值比值的均值和变异系数分别为0.81和0.21,后验模型的预测值更接近试验值,能够更加准确预测PC梁斜裂缝倾角。
Abstract:
In view of the inclined crack angle of prestressed concrete(PC)beams, the formulas recommended by national codes are quite different, and there is no clear theoretical model. Based on the Bayesian theory and the introduction of Markov Chain-Monte Carlo(MCMC)efficient sampling method, the selected calculation formula of inclined crack angle of prestressed concrete beams was used as the Bayesian prior model. Based on the collected 45 groups of inclined crack data, considering stirrup reinforcement ratio, stirrup strength, concrete compressive strength, shear span ratio and effective prestress, the modified calculation model of inclined crack angle was established. The results show that the mean and coefficient of variation of the ratio of predicted and experimental values of the prior model are 0.68 and 0.26 respectively. The mean and coefficient of variation of the ratio of predicted and experimental values of the posterior model are 0.98 and 0.25 respectively, and the predicted value is closer to the experimental value. Based on the inclined crack angle measured by the shear test of PC hollow slab beam, the proposed posterior model is verified,and the mean and coefficient of variation of the ratio of predicted value and experimental value of the prior model are 0.57 and 0.19 respectively. The mean and coefficient of variation of the ratio of predicted value and experimental value of the posterior model are 0.81 and 0.21 respectively. The predicted value of the posterior model is closer to the experimental value, which can more accurately predict the inclined crack angle of PC beams.

参考文献/References:

[1] 肖光宏,江炳章.考虑预应力度的部分预应力混凝土梁抗剪强度的试验研究[J].重庆交通学院学报,1988,7(3):70-83.
XIAO Guang-hong,JIANG Bing-zhang.Experimental Research on Ultimate Shear Strength of Partially Prestressed Concrete with Considering[J].Journal of Chongqing Jiaotong University,1988,7(3):70-83.
[2]彭天明,王 南.受集中荷载简支预应力混凝土和部分预应力混凝土梁的抗剪强度[J].重庆交通学院学报,1987,6(4):47-54.
PENG Tian-ming,WANG Nan.Shear Strength of Simply Supported Prestressed Concrete and Partially Prestressed Concrete Beams with Concentrated Load[J].Journal of Chongqing Jiaotong University,1987,6(4):47-54.
[3]AASHTO LRFD Bridge Design Specifications:AASH-TO LRFD-8-2017[S].Washington DC:AASHTO,2017.
[4]Design of Concrete Structures:CSA A23.3-04[S].Toronto:Canadian Standards Association,2004.
[5]车惠民,张开敬,陈开利.预应力对无箍筋混凝土T形梁抗剪强度的影响[J].西南交通大学学报,1984,19(4):1-15.
CHE Hui-min,ZHANG Kai-jing,CHEN Kai-li.The Effects of Prestress on the Shear Strength of Prestressed Concrete T-beams Without Web Reinforcement[J].Journal of Southwest Jiaotong University,1984,19(4):1-15.
[6]混凝土结构设计规范:GB 50010—2010[S].北京:中国建筑工业出版社,2011.
Code for Design of Concrete Structures:GB 50010—2010[S].Beijing:China Architecture & Building Press,2011.
[7]Building Code Requirements for Structural Concrete and Commentary:ACI 318R-05[S].Michigan:American Concrete Institute,2008.
[8]PAN Z F,LI B.Evaluation of Shear Strength Design Methodologies for Slender Shear-critical RC Beams[J].Journal of Structural Engineering,2013,139(4):619-622.
[9]孟少平,王国林,潘钻峰.钢筋混凝土及预应力混凝土梁抗剪设计方法研究[J].建筑结构,2013,43(19):25-29.
MENG Shao-ping,WANG Guo-lin,PAN Zuan-feng.Study on Shear Design Methods for Reinforced and Prestressed Concrete Beams[J].Building Structure,2013,43(19):25-29.
[10]张开敬,马忠国.部分预应力混凝土无箍筋约束箱梁抗剪强度的试验研究[J].西南交通大学学报,1990,25(2):14-22.
ZHANG Kai-jing,MA Zhong-guo.An Experimental Study of the Shear Strength of Restrained PPC Box Girder Without Stirrups[J].Journal of Southwest Jiaotong University,1990,25(2):14-22.
[11]鲍旭初,孙文智,李海光,等.20 m跨径后张法宽幅空心板单梁抗剪破坏性试验研究[J].公路交通科技(应用技术版),2012,8(6):61-63.
BAO Xu-chu,SUN Wen-zhi,LI Hai-guang,et al.Experimental Study on Shear Destructive Strength of 20 m Span Wide-width Hollow Slab Single Beam by Post-tensioning Method[J].Highway Traffic Technology(Application Technology Edition),2012,8(6):61-63.
[12]DE SILVA S,MUTSUYOSHI H,WITCHUKREANGKRAI E.Evaluation of Shear Crack Width in I-shaped Prestressed Reinforced Concrete Beams[J].Journal of Advanced Concrete Technology,2008,6(3):443-458.
[13]DE WILDER K,DE ROECK G,VANDEWALLE L.Experimental Analysis of the Shear Behaviour of Prestressed and Reinforced Concrete Beams[J].European Journal of Environmental and Civil Engineering,2018,22(3):288-314.
[14]DI J,SUN Y F,YU K,et al.Experimental Investigation of Shear Performance of Existing PC Hollow Slab[J].Engineering Structures,2020,211:110451.
[15]ZHENG H,FANG Z,CHEN B.Experimental Study on Shear Behavior of Prestressed Reactive Powder Concrete I-girders[J].Frontiers of Structural and Civil Engineering,2019,13(3):618-627.
[16]WANG J W,LIU J L,ZHANG G H,et al.Method for Computing the Shear Capacity of Prestressed Reinforced Concrete Beams Based on Truss-arch Model[J].International Journal of Structural Integrity,2018,9(5):574-586.
[17]KIM K S.Shear Behavior of Reinforced Concrete Beams and Prestressed Concrete Beams[D].Urbana-Champaign:University of Illinois at Urbana-Champaign,2004.
[18]贾艳敏,刘金亮,王佳伟.先张法PC空心板剪压区裂缝分析及计算[J].世界桥梁,2017,45(2):66-71.
JIA Yan-min,LIU Jin-liang,WANG Jia-wei.Analysis and Calculation of Cracks in Shear-compression Zone of Pre-tensioned Voided PC Slabs[J].World Bridges,2017,45(2):66-71.
[19]胡 勇.装配整体式预应力混凝土梁抗剪性能试验研究[D].南宁:广西大学,2018.
HU Yong.Experimental Research on Shear Resistance Performance of Assembled Monolithic Prestressed Concrete Beam[D].Nanning:Guangxi University,2018.
[20]MARTIN O.Bayesian Analysis with Python Introduction to Statistical Modeling and Probabilistic Programming Using PyMC3 and ArviZ[M].2nd ed.Birmingham:Packt Publishing Ltd.,2018.
[21]韦来生.贝叶斯统计[M].北京:高等教育出版社,2016.
WEI Lai-sheng.Bayesian Statistics[M].Beijing:Higher Education Press,2016.
[22]HE Z Q,LIU Z,JOHN MA Z.Simplified Shear Design of Slender Reinforced Concrete Beams with Stirrups[J].Journal of Structural Engineering,2016,142(2):06015003.
[23]NAAMAN A.Prestressed Concrete Analysis and Design Fundamentals[M].2nd ed.Daejeon:Techno Press,1982.
[24]公路工程结构可靠度设计统一标准:GB/T 50283—1999[S].北京:中国计划出版社,1999.
Unified Standard for Reliability Design of Highway Engineering Structures:GB/T 50283—1999[S].Beijing:China Planning Press,1999.
[25]VILLAMIZAR S,RAMIREZ J A,AGUILAR G.Shear Strength and Behavior of High-strength Concrete Prestressed Beams[J].ACI Structural Journal,2016,114(1):277-289.
[26]KAUFMAN M,RAMIREZ J.Production and Engineering Properties of Concrete Used in Precast Prestressed I-beams for the State of Indiana,Volume I[R].West Lafayette:Purdue University,1988.
[27]吴 涛,刘 喜,邢国华.基于贝叶斯理论的钢筋混凝土柱受剪承载力计算[J].工程力学,2013,30(5):195-201,206.
WU Tao,LIU Xi,XING Guo-hua.Study on the Shear Capacity of Reinforced Concrete Column Based on Bayesian Theory[J].Engineering Mechanics,2013,30(5):195-201,206.

相似文献/References:

[1]王作虎,詹界东,杜修力.无粘结预应力CFRP筋混凝土梁抗弯试验[J].建筑科学与工程学报,2014,31(02):84.
 [J].Journal of Architecture and Civil Engineering,2014,31(05):84.
[2]李富民,杨 俊,施小飞.腐蚀钢绞线预应力混凝土梁的弯曲疲劳性能退化特征[J].建筑科学与工程学报,2016,33(01):22.
 LI Fu-min,YANG Jun,SHI Xiao-fei.Degradation Characteristics of Flexural Fatigue Property of Prestressed Concrete Beam with Corroded Steel Strand[J].Journal of Architecture and Civil Engineering,2016,33(05):22.
[3]方 梅,李 漫,李 杉.钢管混凝土柱-预应力混凝土梁节点抗震性能试验[J].建筑科学与工程学报,2016,33(03):110.
 FANG Mei,LI Man,LI Shan.Experiment on Seismic Performance of Connection BetweenConcrete-filled Steel Tubular Column and Prestressed Concrete Beam[J].Journal of Architecture and Civil Engineering,2016,33(05):110.
[4]王 钧,李 婷,任靖豪.大直径高强钢绞线预应力混凝土梁受力性能[J].建筑科学与工程学报,2017,34(02):103.
 WANG Jun,LI Ting,REN Jing-hao.Mechanical Performances of Prestressed Concrete Beams with Large-diameter High-strength Steel Strands[J].Journal of Architecture and Civil Engineering,2017,34(05):103.
[5]杨 鸥,张晓非,霍静思,等.预应力混凝土梁疲劳性能研究现状[J].建筑科学与工程学报,2017,34(04):85.
 YANG Ou,ZHANG Xiao-fei,HUO Jing-si,et al.Research Status of Fatigue Performance of Prestressed Concrete Beam[J].Journal of Architecture and Civil Engineering,2017,34(05):85.
[6]羊日华,刘 欢,张旭辉,等.腐蚀预应力混凝土梁抗剪性能试验[J].建筑科学与工程学报,2018,35(05):134.
 YANG Ri-hua,LIU Huan,ZHANG Xu-hui,et al.Experiment on Shear Behavior of PC Beams After Prestressed Tendons Corrosion[J].Journal of Architecture and Civil Engineering,2018,35(05):134.

备注/Memo

备注/Memo:
收稿日期:2021-11-21
基金项目:山东省自然科学基金项目(ZR202102260046,ZR202102240664)
作者简介:张 峰(1978-),男,江苏泰州人,教授,博士研究生导师,工学博士,E-mail:zhangfeng2008@sdu.edu.cn。
更新日期/Last Update: 2022-09-30