|本期目录/Table of Contents|

[1]姚欣梅,周绪红,张 辉,等.冷弯薄壁型钢C形梁受剪性能分析[J].建筑科学与工程学报,2018,35(05):152-159.
　YAO Xin-mei,ZHOU Xu-hong,ZHANG Hui,et al.Shear Behavior Analysis of Cold-formed Thin-walled Steel C-shape Beam[J].Journal of Architecture and Civil Engineering,2018,35(05):152-159.
点击复制

冷弯薄壁型钢C形梁受剪性能分析(PDF)
分享到：

《建筑科学与工程学报》[ISSN:1673-2049/CN:61-1442/TU]

卷:
35卷
期数:
2018年05期
页码:
152-159
栏目:
出版日期:
2018-09-03

文章信息/Info

Title:
Shear Behavior Analysis of Cold-formed Thin-walled Steel C-shape Beam
作者:
姚欣梅，周绪红，张 辉，石 宇，管 宇
长安大学建筑工程学院
Author(s):
YAO Xin-mei, ZHOU Xu-hong, ZHANG Hui, SHI Yu, GUAN Yu
School of Civil Engineering, Chang’an University
关键词:
冷弯薄壁型钢; C形梁; 受剪承载力; 有限元分析; 截面特性
Keywords:
cold-formed thin-walled steel;  C-shape beam;  shear bearing capacity;  finite element analysis;  section property
分类号:
-
DOI:
-
文献标志码:
A
摘要:
为研究冷弯薄壁型钢C形梁的受剪性能，在已有试验基础上，采用ABAQUS有限元分析软件建立非线性数值模型，对比试验与有限元结果的受剪承载力、试件破坏特征、荷载跨中挠度曲线等；进而探讨了C形梁剪跨比、腹板高厚比、腹板厚度以及钢材强度等因素对冷弯薄壁型钢C形梁受剪性能的影响。结果表明：剪跨比是影响冷弯薄壁型钢C形梁破坏特征的主要因素，当剪跨比在0.5~1.1之间时，C形梁处于纯剪切受力状态，此时破坏模式为剪切屈服；当剪跨比在1.1~2之间时，C形梁处于弯剪受力状态，此时破坏模式为弯剪破坏；随剪跨比的增加，冷弯薄壁型钢C形梁的受剪承载力及刚度均减小；当腹板高厚比在50~150之间时，冷弯薄壁型钢C形梁的受剪承载力及刚度随腹板高厚比增加而增大，跨中挠度减小；随着腹板厚度的增加，冷弯薄壁型钢C形梁受剪承载力及刚度明显提高；增加钢材强度可显著提高冷弯薄壁型钢C形梁受剪承载力，但对冷弯薄壁型钢C形梁的刚度影响较小。
Abstract:
In order to investigate the shear behavior of cold-formed thin-walled steel C-shape beam, a nonlinear numerical model was built up through the finite element analysis software ABAQUS based on previous experimental study. The correctness of the modeling method was verified by comparing the results of finite element model and that of experiment. The compared results included the shear bearing capacity, specimen failure characteristics and load-mid span deflection curves. Then the effects of shear span ratio, web height to depth ratio, web depth and steel strength on the shear behavior of cold-formed thin-walled steel C-shape beam were investigated. The results show that shear span ratio is the main factor determining the failure characteristics of cold-formed thin-walled steel C-shape beam; when the shear span ratio is at 0.5-1.1, the C-shape beam is in pure shear and the corresponding failure mode is yield stress; when the shear span ratio is at 1.1-2, the C-shape beam is subjected to combined action of bending-shear and the corresponding failure mode is bending-shear failure; the shear bearing capacity and the stiffness of C-shape beam decrease with the increase of shear span ratio; when the web height to thickness ratio is at 50-150, the shear bearing capacity and stiffness of the C-shape beam raise with the increase of web height to thickness ratio, and the mid-span deflection decreases; with the increase of web thickness, the shear bearing capacity and stiffness are obviously improved; the steel strength has significant influence on the shear bearing capacity of the beam, but has little effect on the stiffness of it.

参考文献/References:

相似文献/References:

[1]高婷婷,周绪红,刘永健,等.采用GB 50018—2002计算壁厚小于2 mm的受弯构件承载力的适用性分析[J].建筑科学与工程学报,2013,30(04):91.
　GAO Ting-ting,ZHOU Xu-hong,LIU Yong-jian,et al.Applicability Analysis of Bear Capacity of Flexural Members with Thickness Less than 2 mm Calculated Using GB 50018—2002[J].Journal of Architecture and Civil Engineering,2013,30(05):91.
[2]石 宇,王身伟,刘永健.冷弯薄壁型钢单颗自攻螺钉抗剪连接性能研究[J].建筑科学与工程学报,2014,31(02):57.
[3]石宇,周绪红,刘永健.冷弯薄壁卷边槽钢偏心受压构件承载力计算的折减强度法[J].建筑科学与工程学报,2011,28(03):40.
　SHI Yu,ZHOU Xu-hong,LIU Yong-jian.Strength-reduction Method for Load-carrying Capacity of Cold-formed Thin-walled Lipped Channel Members Under Eccentric Compression[J].Journal of Architecture and Civil Engineering,2011,28(05):40.
[4]刘向斌,周天华,聂少锋,等.冷弯薄壁型钢开口三肢拼合立柱轴压性能有限元分析[J].建筑科学与工程学报,2011,28(03):119.
　LIU Xiang-bin,ZHOU Tian-hua,NIE Shao-feng,et al.Finite Element Analysis of Cold-formed Thin-walled Steel Three Open Limbs Built-up Columns Under Axial Compression[J].Journal of Architecture and Civil Engineering,2011,28(05):119.
[5]聂少锋,周天华,熊智刚,等.冷弯薄壁型钢开洞组合墙体抗剪性能研究[J].建筑科学与工程学报,2012,29(01):101.
　NIE Shao-feng,ZHOU Tian-hua,XIONG Zhi-gang,et al.Research on Shear Resistance Behavior of Cold-formed Thin-walled Steel Composite Walls with Opening[J].Journal of Architecture and Civil Engineering,2012,29(05):101.
[6]刘向斌,周天华,何鑫,等.冷弯薄壁型钢住宅结构整体扭转效应分析[J].建筑科学与工程学报,2012,29(02):83.
　LIU Xiang-bin,ZHOU Tian-hua,HE Xin,et al.Analysis of Torsional Effect of Cold-formed Thin-walled Steel Residence Structure[J].Journal of Architecture and Civil Engineering,2012,29(05):83.
[7]周绪红,李喆,刘永健,等.冷弯薄壁型钢拼合截面柱轴压承载力计算[J].建筑科学与工程学报,2012,29(04):1.
　ZHOU Xu-hong,LI Zhe,LIU Yong-jian,et al.Calculation Method for Bearing Capacity of Cold-formed Steel Built-up Columns Under Axial Compression[J].Journal of Architecture and Civil Engineering,2012,29(05):1.
[8]刘晶波,陈鸣,刘祥庆,等.低层冷弯薄壁型钢结构住宅整体性能分析[J].建筑科学与工程学报,2008,25(04):6.
　LIU Jing-bo,CHEN Ming,LIU Xiang-qing,et al.Integral Behavior Analysis of Cold-formed Thin-walled Steel Framing System of Low-rise Residential Buildings[J].Journal of Architecture and Civil Engineering,2008,25(05):6.
[9]周绪红,李艳敏,石宇,等.竖向荷载作用下冷弯薄壁型钢墙架柱的承载力[J].建筑科学与工程学报,2006,23(03):7.
　ZHOU Xu-hong,LI Yan-min,SHI Yu,et al.Bearing Capacity of Cold-Formed Thin-WalledSteel Wall Stud Under Vertical Load[J].Journal of Architecture and Civil Engineering,2006,23(05):7.
[10]管 宇,周绪红,石 宇,等.多层冷弯薄壁型钢住宅体系动力时程分析[J].建筑科学与工程学报,2018,35(05):142.
　GUAN Yu,ZHOU Xu-hong,SHI Yu,et al.Dynamic Time History Analysis for Mid-rise Cold-formed Thin-walled Steel Residential Building System[J].Journal of Architecture and Civil Engineering,2018,35(05):142.

备注/Memo

备注/Memo:
更新日期/Last Update: 2018-09-03